Small RTD Temperature Probe

39 Reviews
$14.98

Details

SMALL RTD TEMPERATURE PROBE

The RTD is the temperature probe attached to the inside of the cooking chamber on the left wall. It has two leads that run to the controller.

FITS MODELS: RT-340, RT-300

 

FEATURES

  • 4” stainless steel probe
  • Standard connections

Ratings & Reviews

39 reviews

  • 3 stars
  • 0 reviews
  • 2 stars
  • 0 reviews
  • 1 star
  • 0 reviews
8/12/2017 3:00:00 pm

Great grill/smoker from RecTec, also outstanding customer servic0e!!!

Richard White -

I had a potential problem with the temp probe and, as usual, RecTec was quick to send a replacement free of charge to enable me to continue to use my unit.

12/21/2016 3:00:00 pm

Great little grill

Carl -

It was nice to purchase a product from the Internet that worked just like it was advertised. If your mess<br>your food up it will be your fault and not the grill. I have never wanted to cook anothing period. Now i look forward to using my mini every chance I get. I called the customer service once and they were awesome.

11/8/2017 3:00:00 pm

i am really happy with the mini

Glenn -

This is my first pellet grill and i am really enjoying it. Actually i wish i would have purchased the 680 just for the extra space. <br>I was currently using a TEC grill and for what i use the grill for they are not even close. I pefer the rec tek hands down , no question.

10/11/2017 3:00:00 pm

its great!!!!

stan nordel -

looked at many pellet grills ....this one seem the best ......for quality ...ease of cleaning ....folding legs....temp control ......great product

7/20/2017 3:00:00 pm

Perfect temp control, installation not easy

Henry Matthes -

The installation of the probe is simple. The running of the wires through the firewall, then around the fax box toward the grill front, then to the RTD connectors is not easy.<br>I'm not too coordinated but I finally fished out the wires -- I was afraid to damage them.<br>A picture would be handy. Maybe I should use all my camera gear and build a how-to page!

2/19/2019 3:00:00 pm

Randall Smeltzer

Randall Smeltzer -

Randall Smeltzer works well with 680 controller on my bullseye

9/5/2017 3:00:00 pm

Rec Tec Mini RTD temp probe

Dan Graves -

I was having trouble with my temp in my mini running about 35 degrees below set point on grill. called Rec Tec and they sent out new probe right away I got it the next day!!!! Installed yesterday without problem and now will see how temp does. Great customer service!!!!!! Really great company to deal with.

1/26/2017 3:00:00 pm

Replace Temp Probe

Frank -

Thanks for the instructions to replace the temperature sensor. However, I found a very simple way to replace it without tearing the whole unit apart. It may or may not be your approved method but I found that I would not break or forget how to replace all the wires after disconnected.. OK, here goes... start by getting access to the bottom by removing the four screws and removing the grate. find the wire bundle that has the two plastic tie wraps and cut them. now find the two wires coming from the sensor, they will be on the bottom right. Do not disconnect them from the terminal board yet. Next disconnect the sensor unit in the tank, do not lose the two lock washers and nuts. Pull the sensor out of the tank slowly cut the wires of the sensor at the base of the unit , save the deflector from the sensor.. Wrap one wire from the sensor around the connector of the new sensor unit slowly pull the wire from the circuit board. The connector will fit through the wall of the tank salon as you feed it gently. Pull the wire through the unit and you are done. Just replace the wires on the board. I really didn’t want to mess with all of the mess removing the hopper and all the other stuff. Call me if you would like me to clarify anything.. I have always tried to take less time and effort when making a repair or overhaul..

6/5/2017 3:00:00 pm

replacement

0 -

My original probe when shipped with grill was bent. It appeared to work but I would get an overheating error. Called rechecked and they sent me out a replacement under warranty. It was fairly easy to replace and has worked great ever since without anymore overheating errors.

7/30/2018 3:00:00 pm

Replacement part

Rick Hagen -

The customer service at Rec Tec never lets you down! I've owned a 300 mini for about two years, and I started experiencing problems with the temp bouncing around, and then error coding out. With out hesitation Rec Tec sent out a new probe and control board free of charge. It was a simple swap out, and my smoker is running like a champ again. I don't know why anyone would chose a different brand.

Write a Review